With winter approaching and cooler weather upon us, people are beginning to load their their wood stoves with firewood. Hopefully they have purchased (or procured themselves) wood from early this year or last year, so that it has had a chance to dry out (‘season’). Burning wet wood or only partially seasoned wood in your wood stove is not a very good idea, and here’s why…
Wet wood provides MUCH LESS heat, and causes MUCH MORE creosote to form in the chimney.
Today’s airtight wood stoves extract heat from wood in two ways.
1. The primary source of heat from a wood stove is the combustion of the wood itself.
2. The secondary source of heat is from the combustion of the gasified resins and unburned wood particles from the primary fire.
Unless your wood stove is a very primitive model, you’ll find a baffle plate of some kind near the top of your stove, between the fire chamber and the flue outlet. This is where the secondary burn occurs, and where your stove creates up to half the heat it delivers to you. The amount of secondary combustion that occurs varies widely from model to model, mainly due to advances in heat extraction technology over the years…
A twelve-year-old baffled airtight can be presumed to operate at about 45% efficiency, while many of today’s EPA approved wood stoves exceed 70% efficiency. The big difference between the older wood stoves and today’s wood stoves can be found in the baffle area, where newer, more sophisticated techniques have been incorporated to re-burn the exhaust gases.
When you add an unseasoned or wet piece of wood to your fire, the water contained in the wood heats up and turns to steam, which mixes with the exhaust gases and extinguishes the secondary burn. Regardless of how sophisticated your baffle system is, this cuts your heat output by up to 50%, and results in cool, water-laden exhaust filled with unburned particles and exhaust gases. This wet, heavy, high-density smoke travels very slowly up the chimney, where it cools even further, condensing onto the walls of the flue and causing excessive creosote formation. So, when you burn unseasoned or wet wood, you dramatically DECREASE your heat output, while dramatically INCREASING the likelihood of chimney fires.
Another drawback to burning wet or unseasoned wood is creosote formation on the viewing window. No matter how good the airwash design that keeps the window clean, it won’t work when the firebox is full of wet smoke. A blackened viewing window is one of the most reliable indicators that the wood is improperly seasoned.
Have you ever wondered what is the best firewood to use for heating and burning in a wood stove? Ever wondered how much heat that a particular wood species will provide when burned?
Did you know that one cord of firewood provides the heat equivalent to that produced by burning 200 to 250 gallons of heating oil, depending on the type of hardwood you are using?
A cord of Oak will burn about 29 Million BTU’s, and is one of the better (more efficient) types of wood to heat with. Oak is very hard and dense, and will burn for a long time compared with many others.
On the flip-side, a cord of Pine will only provide 60% of the heat as Oak, while Cedar will provide less than half the heat as Oak.
If we compared the wood burning capacity by weight, instead of by cord, most wood would produce about the same amount of heat. The difference is that dense hard woods are heavier, pack more heat, and therefore a cord (or any quantity) of hard wood will produce more heat than the same quantity of a softer wood.
For heating, in general it is best to consume dense hard woods. Hardwoods, or woods from broadleaved trees, tend to be denser than softwoods or woods from conifers.
In case you wondered, a standard cord of wood is 128 cubic feet – 8 feet x 4 feet x 4 feet.
Really though, the best firewood is going to be whatever is locally available to you, so long as it’s dry and fits in your stove. If you have a choice though, choose a hardwood for fewer trips to the log pile.
List of wood species, heating BTU’s per cord, from most to least,
(not all inclusive)
In case you were wondering about those waxy energy ‘Duraflame’ type fire-logs…
Typical Oak firewood has about 8,500 BTU’s per pound.
A typical wax-fiber firelog has about 14,000 BTU’s per pound.
While energy logs might be a nice quick fix for a fire, it’s an expensive fire…
NOTE: Be wary of using soft and oily woods like Pine in a stove or fireplace due the buildup of creosote (a residue that is highly flammable) in the flu over time. Pine makes for a great firestarter because it burns very hot and fast, but not good for long-term use.
The bottom line: Think ahead, and allow enough time for your wood to season before use in your wood stove.
by Ken Jorgustin – modernsurvivalblog.com
Before It's News
All Self Sustained
Patriot Net Daily
Survivalist News Network
My Child Behaviour
My Daily Informer
My Family Survival Plan
The Garden Prepper
The Married Gang
The Prepper Dome
US Crisis Preppers